TI, its suppliers msp430 usb debug interface device providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice. The MSP-FET430UIF is no longer recommended for new designs. The MSP-FET430UIF is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. D/FW is an open source, experimental, and unofficial firmware for MSP-FET430UIF and eZ430U debug interface and associated host side control programs. Host side programs are designed to work with any modern UNIX operating systems (e.g. Linux, *BSD). Im currently using MSP430F427A as a chip and had made a debugger board for it with jtag interface. I have acquired MSP430 USB-Debug Interface ( MSP-FET430UIF ) to connect to my debugger board via JTAG, the problem is i really cant find anywhere the driver for this device.
> > -- Aaron > > OneStone said the following on 3/30/2010 1:18 PM: > > > > RALMFCO > > > > What on earth do you think MSP-FET430U(sb)I(nter)F(ace) - VCP MIGHT BE > > OTHER THAN THE USB interface. Did you actually try programming > > something, OR COMMUNICATING WITH SOMETHING?? Or did you just check the > > drivers Not see the exact wording TI USB FET and assume the worse? > > > > perhaps you should try waiting until you encounter a problem before you > > start imagining them. > > > > AL > > > > Aaron Greer wrote: > > > I've searched the archives looking at past driver issues, but couldn't > > > find anything that sounded quite like what's happening here. > > > > > > A little background: I previously had Quadravox AQ430X installed on > > > this machine as well as an older version of the IAR Kickstart IDE. Both > > > have been uninstalled completely via the add/remove programs wizard.
In case the interface is not listed here it is either not connected or the CDC driver wasn't installed. Please check or re-run the installer. If the interface is listed but doesn't work, check the IDE specific FAQ. Q5: How can I tell whether my MSP-FET430 was updated to the MSP430.DLLv3 or not? A5: When you connect the interface, the LEDs will show which version you are using: • Older, un-updated interfaces will blink: red-red-red-green (green remains on) • Updated v3 interfaces will just light up the green LED, when connecting to the PC Code Composer Studio Q6: I get an error message ' Error Initializing Emulator: Only one MSP430 device can be accessed at a time per each CCS.'
One is the virtual com port (VCP), the other is > the flash emulation tool (FET). This time, it appeared to only load the > VCP. 
In addition, I was unable to download any programs or debug any > devices. I was getting a failed communication error. I have since > uninstalled and reinstalled IAR and rebooted several times. It appears > that I am now able to download and debug code, but I'm still only seeing > the VCP in the device manager.
This was without a doubt the most unstable software I've ever come across. DVD that came with the 4358 board or FET-UIF definitely outdated and did not install low-level USB drivers, after 2 weeks of BSOD's finally works.
Msp Fet430uif Driver
This opens using the 2008 CD the following screen. Use boost::mutex instead of std::mutex. Casino mond slowenien adresse. Daraufhin offnet sich ein Fenster bei ms;-fet430uif man nach gewunschter Msp-fet430uif windows 7 driver gefragt wird. The DLL is implemented in C++ and follows an object based design, which is host operating system independent. All drivers are Microsoft WHQL msp-fet4330uif. MSPDS-USB-DRIVERS: Stand-alone Driver Installer for USB Low-Level Drivers Free ACTIVE 1.
Msp-fet430uif Pinout
• MSP-FET430UIF debugger update When a debug session is being opened, the IDE will ask you to perform a debugger update. BEFORE continuing, please ensure that no other debuggers are connected to your PC. You also need to have administrator rights on the PC that you are using. Click 'Update' in the IDE dialog. • The update will happen in a fully automated manner. It will take a few minutes, you will also notice that Windows will disconnect from the debugger during the process and that a new USB device will be installed. That's normal.